.pst viewer - Where download the PST file viewer? Free to use viewer for Outlook PST files. How to view PST folder? Microsoft PST file viewer.

pst reader - Microsoft Outlook PST reader. Free Microsoft PST reader. Fastest Outlook 2003 PST reader software. Best PST readers.

pst viewer - Microsoft Outlook .PST viewer. Outlook viewer for .PST files. Free Outlook PST email viewer. Download 2003 PST viewer.
HOME ABOUT ME PRODUCTS PAGE HISTORY MYLINKS PAGE NEW PRODUCTS
Translating the image by using carbon paper, one must remember that the lines of the pattern should not be bold, to fabric and thread in the implementation of embroidery is not dirty. Therefore, a new carbon paper tentatively be wiped dry with cotton or cloth. On the thin transparent fabric pattern transferred through the highlights. On glass under which is placed a lamp, put the tracing paper with a clear pattern, and on top of her well-stretched fabric. Sharpened pencil encircle a pattern that is visible through the fabric. Workplace embroiderers. In order to embroider it was convenient, it is necessary to organize the workplace. Table with all the appliances and tools should stand so that light falling on the work of the left side. If the table is not a box, threads can be stored in an embroidered bag, tools - in a special box and tracing paper sheets with patterns - in the folder. The choice of fabric and thread for hand embroidery depends on the purpose of the product, the nature of the pattern and manner of its execution. The strength of thread test, stretching her hands: a good thread should bounce and did not immediately explode. The strength of color of thread can be verified if we put the samples in the sun. Securing the thread into the fabric. The embroidery on the working thread will never make nodules. Wrong side of embroidered items must be clean and neat. Threaded fasten on the front side of the fabric of the place where the embroidery will be located. If embroidery is necessary to take an even number of strands, such as 6 thread floss, the floss from the separate threads (one) 3 threads. Put them together and pass a needle with two ends. Needle and thread do the stitch and pull the thread from the fabric as long as remain a small tip in the form of a loop, which was formed by folding the thread twice. In this loop of thread the needle with the working thread and tighten. If the stitching in one, three, five threads, then fix a working thread a different way. Make a small stitch on the fabric, pull the thread, leaving a small tip. This is the tip of the threads attach to the fabric of the second smallest stitch, placing it across the tip of the thread. Excess end of the thread cut. Place securing thread close stitches of embroidery. Can be left on the wrong side at the beginning of the end of the thread length of 5-6 cm and gently run a few stitches on the front side of the fabric. Then vdet to another needle left on the wrong side of the end of the thread and make a few stitches under just made embroidery. The balance of thread cut. At the end of a working thread embroidery is fixed on the wrong side, making a few stitches in the wrong place, where the embroidery. You can pin and thread on the front side of the fabric, dragging her by the embroidery stitches, or to make a few stitches in place, which will later be closed with embroidery. Treatment of embroidered products. Wash items with colored embroidery should be very careful in warm water. They can not soak, pour the boiling water and simmer. Wash the product must be well rinsed in cold water, wring out and wrap a few minutes in a terry towel or sheet. Stroking the product must be moist from the inside. After ironing, the product must be in expanded form up until cools down. Types of joints. Chain stitch is a continuous series of loops that go from one another. Suture can be performed either hoop, or without them. In both cases, stitches are necessary to carry out the movement to the needle itself. Embroidering without the hoop, then make sure that the fabric is not contracted, and the loop suture had a rounded shape. If embroidery thread, folded in half, then fastening threads on the fabric can be the first loop of suture vestibule. After fixing the working thread lay a loop in the direction from left to right down, and the needle entering the tissue in the middle of the first loop, the point from which the train came to the front side of the fabric. Pokes the needle of 4-5 filaments tissue below the first loop so that the loop of thread was working under the needle. So embroider a straight line, counting the same number of threads for each stitch fabric.